-
FT30C型玻璃钢电机外接式轴流通风机
FT30C型玻璃钢电机外接式轴流通风机具有结构合理、设计简单、静压及效率高、防腐性能良好、噪音低、运转平稳、机械振动小、气流顺畅等特点。该系列风机电机装配在风机筒体上部，有可调的电机支承座板，采用角带传动，从而使风机所输送的各种耐腐性气体与电机隔离，保证电机使用寿命。风筒内采用外沟球面万向轴承座，具有体积小、密封性能好等到优点。该系列风机主要适用于一般工业管道串联加压、送风及排气使用。所输送气体不允许含有粘性物质、所含粉尘及硬质颗粒≤150mg/m3、气体温度≤60℃、相对湿度≤99%。 -
FT30C type FRP axial flow fan series
The FT30C type glass fiber reinforced plastic motor external axial flow fan has the characteristics of reasonable structure, simple design, high static pressure and efficiency, good anticorrosive performance, low noise, smooth operation, small mechanical vibration and smooth flow. The series fan motor is assembled on the upper part of the fan body, with adjustable motor supporting seat plate and angular belt drive, so that all kinds of decay resistant gas conveyed by the fan can be isolated from the motor to ensurethe service life of the motor. The outer groove spherical universal bearing seat is used in the winder, which has the advantages of small volume and good sealing performance. This series of fans are mainly applicable to the series pressurization, air supply and exhaust use of general industrial pipes. The gas is not allowed to contain viscous substances, dust and hard particles is less than or equal to 150mg/m3, the gas temperature are less than 60, the relative humidity is less than 99%.
| 机 号 Model(No) | ||||
|---|---|---|---|---|
| 功 率 Power(Kw) | 转 速 Speed(r/min) | 流 量 Volume(M3/h) | 全 压 Pressure(Pa) | |
| 3.5C | 0.55 | 1450 | 2500 | 40 |
| 4C | 0.75 | 1600 | 4000 | 86 |
| 0.55 | 1450 | 3500 | 66 | |
| 5C | 1.5 | 1600 | 8460 | 100 |
| 1.1 | 1450 | 7667 | 82 | |
| 6C | 2.2 | 1600 | 14000 | 179 |
| 1.5 | 1450 | 11590 | 123 | |
| 7C | 3 | 1450 | 19000 | 226 |
| 8C | 4 | 1450 | 24500 | 221 |
| 9C | 5.5 | 1450 | 31421 | 215 |
| 10C | 4 | 960 | 27755 | 134 |
| 11.2C | 7.5 | 960 | 43673 | 215 |
外形及安装尺寸示意图 Lnstallation size diagram
产品为人工实物测量会有一定误差，相关数据仅作参考，以收到的实物为准。 单位Unit: mm(毫米）
| 机 号 | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| 外形尺寸 Shape size | 底架尺寸 Bottom frane size | |||||||||
| NO | D | Φ1 | Φ2 | A1 | A2 | B1 | B2 | H1 | H2 | Φd |
| 3.5C | 355 | 380 | 410 | 220 | 625 | 400 | 450 | 290 | 350 | 12 |
| 4C | 410 | 435 | 466 | 245 | 660 | 400 | 450 | 300 | 400 | 12 |
| 5C | 555 | 518 | 608 | 315 | 868 | 423 | 467 | 550 | 600 | 12 |
| 6C | 655 | 605 | 705 | 362 | 978 | 445 | 500 | 670 | 710 | 12 |
| 7C | 710 | 735 | 790 | 408 | 1008 | 525 | 580 | 743 | 805 | 12 |
| 8C | 810 | 850 | 890 | 458 | 1130 | 620 | 660 | 815 | 900 | 12 |
| 9C | 948 | 905 | 1010 | 505 | 1300 | 682 | 745 | 900 | 995 | 12 |
| 10C | 1010 | 1050 | 1090 | 580 | 1318 | 735 | 800 | 980 | 1090 | 12 |
所有评论仅代表网友意见，与本站立场无关。